License Plate Light Requirements for Trucks and Trailers
Every state requires the rear license plate to be lit at night with a white light, and the plate has to be readable from 50 feet behind the vehicle. That is the rule in Texas, Washington and Oklahoma, and the wording is close to identical in most other states. The details that trip up truck and trailer owners are the lamp’s color, how it is wired, how it is sealed against water, and what happens when it quits on the road.
This guide covers what the statutes say, what the federal standard adds, what a burned-out lamp can cost you, and how to pick a replacement that keeps working on a long haul.
TL;DR
- The rear plate must be lit with white light and legible from 50 feet at night. State codes such as those in Washington and Texas use this standard.
- The plate lamp normally has to come on with your headlamps or other required lighting, so it should share that circuit.
- Federal rules (FMVSS 108) set the photometric performance of new plate lamps. State law governs what you can be ticketed for on the road.
- A dead plate light is a common reason for a traffic stop and often a fix-it ticket. For a commercial driver, a stop is the last thing a tight schedule needs.
- Sealed, waterproof housings and corrosion-resistant wiring prevent most plate light failures.
Table of Contents
- What the law says about license plate lights
- What FMVSS 108 adds
- What a burned-out plate light can cost you
- Why plate lights fail, and how to prevent it
- Choosing a plate lamp for a truck or trailer
- Our perspective: treat the plate light as part of the lighting system
- Plate lights built for hard hauling
- Night visibility beyond the plate
- FAQ
- Sources
What the law says about license plate lights
There is no single national traffic statute for plate lamps. Each state writes its own equipment law, and each one has been modeled on the same template. Read three of them side by side and the pattern is obvious.
- Color: white. Texas and Washington both require the plate to be lit with white light.
- Legibility: the plate must be readable from 50 feet to the rear. Maryland’s regulations are written around the same test.
- Timing: the lamp must be lit whenever the headlamps are on. Oklahoma ties the plate lamp to the clearance lamps, headlamps, combined headlamps and auxiliary driving lamps, or fog lamps.
- Applies to trailers: the statutes cover “every motor vehicle, trailer, semitrailer and pole trailer,” so a tractor and a trailer each carry their own obligation. Louisiana’s statute is typical in covering trailers and any vehicle drawn at the end of a combination.
The wording differs in small ways. Ohio and Kansas each combine tail lamp and plate lamp rules in one section, which is why many people search for “tail light” law when they really mean the plate light. Oklahoma goes a step further and limits you to no more than two separate white plate lamps. It also treats a plate framed or surrounded by extra lamps as a violation, so decorative lighting around the plate is not a safe upgrade there.
Because these laws are state-specific, check your own state’s vehicle code, and the codes of states you run through regularly, before you modify a setup.
Does the plate light have to be a separate lamp?
Not necessarily. The common statutory phrasing allows either a tail lamp or a separate lamp to do the job, as long as it lights the plate with white light and makes it legible. That is why some trailers use a combination fixture that handles stop, turn, tail and plate illumination in one housing. If you go that route, the fixture has to actually deliver white light onto the plate. A red-only lens pointed at the rear does not meet the requirement.
What if the plate is not required in your state?
Some drivers point out that certain trailers do not need a plate in every situation. One widely read Texas discussion argues that the plate lamp requirement attaches when a plate is displayed on the vehicle, not just when one is required. We would not build a compliance plan on a technicality. If a plate is on the back of the rig, light it.
What FMVSS 108 adds
State statutes tell you what is legal to operate. The federal standard, FMVSS No. 108, tells manufacturers what a plate lamp must do when it is built and sold on a new vehicle or as equipment. It defines a license plate lamp simply as a lamp used to illuminate the license plate on the rear of a vehicle, then sets performance rules around it.
The parts that matter to a fleet or a trailer builder:
- Minimum illumination. The standard calls for a minimum of 8 lux (0.75 foot-candles) at the specified target points on the plate, measured on a 150 mm by 300 mm test plate.
- Even coverage. For most vehicles, the ratio between the brightest and dimmest readings on the plate is limited to 20:1. A lamp that blasts one corner and leaves the rest dark fails the intent of the rule.
- Light angle. The standard includes an incident light angle requirement of 8 degrees, which keeps the light source from washing out the plate surface with glare.
- Combination lamps. The standard does not allow a plate lamp to be optically combined with other required rear lamps if that prevents the plate lamp or the other lamps from meeting their own requirements.
- Obstructed lamps. Federal interpretation recognizes that auxiliary lamps may be needed when a trailer platform or cargo blocks the view of required rear lamps.
In practice: buy lamps marked for DOT and SAE compliance, mount them where they illuminate the whole plate, and do not assume a bright LED is a compliant one. Brightness and evenness are different things.
What a burned-out plate light can cost you
On paper it is a small offense. In practice it is one of the easiest reasons for an officer to pull you over. According to FindLaw’s overview of plate light tickets, a burned-out front or rear plate light can earn a ticket, often called a fix-it ticket. Those typically give you a window to repair the lamp and show proof of correction, and that window commonly runs about 10 to 30 days depending on where you are. Fines vary by jurisdiction, and repeat offenses can bring larger penalties.
The ticket is rarely the real cost. A stop at night means an inspection of your paperwork, your load and your equipment, and it means time off the road. For an owner-operator or a dispatcher trying to hold a delivery window, preventing the stop is worth more than the fine.
Some local situations make it worse:
- Plates that are dirty, covered or partly hidden by a hitch, a bumper or a cargo overhang are cited under display and visibility rules, sometimes separately from the lamp. Arkansas, for example, regulates how a plate is displayed under its own statutes, separate from the requirement to have a plate at all.
- Some states run periodic equipment inspections. Maryland’s inspection procedure, for instance, has the inspector check lamps for function and for color contrary to law.
- A lamp that works only intermittently can pass your pre-trip check and fail at 2 a.m. Treat flickering as a failure.
Why plate lights fail, and how to prevent it
Plate lamps sit low and at the very back of the rig. They collect road spray, salt, pressure washer blasts and vibration. Industry commentary on plate lights points to waterproofing as the first thing to look for because moisture and corrosion are leading causes of premature failure.
The failure points we see most often are:
- Water in the housing. A lens that is not truly sealed fogs, shorts and dies. Look for an ingress protection rating such as IP67, which indicates the lamp is built to handle temporary immersion.
- Bad grounds. Trailer lights depend on a clean ground. Rust at the ground point makes lamps dim or flicker, and it often takes the other trailer lights with it.
- Cracked or thin wiring. Undersized or poor-quality wire that is bent over a hitch ages quickly. Thicker copper conductors hold up better and carry current with less voltage drop.
- Unprotected connectors. An open spade or bullet connector will corrode. Use sealed connectors, and use grommets where wire passes through metal so the insulation is not cut by a sharp edge.
- Cheap halogen bulbs. Filament bulbs break on rough roads. LEDs have no filament and tend to run cooler, which is why most fleets have moved to them.
A quick pre-trip check
It takes less than a minute at the back of the trailer:
- Turn on the running lights or headlamps with the trailer plugged in.
- Walk to the rear and confirm the plate is lit, even and white, with no dark corners.
- Look at the lens for moisture, cracks or a lifted seal.
- Wipe the plate clean. Mud can defeat a perfectly good lamp.
- Give the wiring a gentle tug near the lamp to check for loose or corroded connections.
Choosing a plate lamp for a truck or trailer
What to weigh before you buy:
| Criterion | What to look for | Why it matters |
|---|---|---|
| Compliance marking | DOT and SAE marking, and FMVSS 108 where stated | Shows the lamp is designed to meet federal equipment rules |
| Light color | White output onto the plate | State statutes require white light |
| Sealing | IP67 or better, sealed housing and lens | Water and salt are the top failure causes |
| Voltage | 12V DC, or a 10V to 30V range if you run mixed equipment | Matches the vehicle or trailer circuit |
| Size and mount | Surface mount sized to your bracket or tag area | Lamp must cover the full plate evenly |
| Lamp count | One or two, as local law allows | Some states cap the number of separate plate lamps |
| Wiring | Heavy gauge copper, sealed connectors | Keeps the lamp lit over years of vibration |
If you tow with a pickup and pull equipment, boats or RVs, the same rules apply. A trailer is a vehicle in every state code listed above.
Our perspective: treat the plate light as part of the lighting system

Most plate light trouble starts at the wiring, not at the lamp. We build and sell lighting for trucks and trailers, and the failures that come back to us nearly always involve water getting into a housing, or a ground or connector that was never protected. That is why we focus on leak-proof housings, brighter LEDs and thicker copper wiring, and why our products are built to exceed DOT standards rather than just meet them.
Our advice to fleet managers and trailer builders is simple. Do not spec the plate lamp last. Pick a sealed, DOT-compliant lamp, use quality wire and a proper ground, and add it to your pre-trip inspection checklist. A few dollars saved on a plate light is quickly lost in a roadside stop. Those who rely on their rigs every day should expect a plate light to last as long as the trailer’s other lamps do.
— All
Plate lights built for hard hauling
If you are replacing a lamp or building out a trailer, we carry plate lighting in several sizes and configurations, all with sealed construction for wet and salty conditions:
- The Heavy Duty 4"x2" surface-mount 6 LED plate lights are listed as DOT, SAE L and FMVSS certified and IP67 waterproof rated.
- For tight mounting spaces, the 3"x1.6" 4 LED plate light and the 2"x1.65" 6 LED set are compact options.
- Want one fixture to do more? The 36 LED combination stop, turn, tail and license plate light puts red and white output in one housing.
- For boat trailers that get dunked, the 12V low profile submersible trailer light kit includes a 25 ft 4-pin wiring harness and bracket.
Browse the full range of lighting, wiring and reflective products on the All Star Truck Parts home page.
Night visibility beyond the plate
A lit plate is one piece of being seen and seeing. If you drive a lot after dark, the glass in front of you matters too. Window film that is too dark cuts how much you can see at night, so it is worth reading about which tint levels and films are safest for night driving before you choose one. On the back of the rig, reflective tape and marker lights do the work that the plate lamp cannot, and they are worth checking in the same pre-trip walk-around.
FAQ
What color must a license plate light be?
White. State vehicle codes, including those of Texas and Washington, require the rear plate to be lit with white light. Blue, red or colored lamps aimed at the plate can bring a citation, so keep the plate lamp white.
Can I get pulled over for a license plate light that is out?
Yes. A burned-out plate light is a recognized equipment violation, and FindLaw notes it can lead to a traffic ticket, often a fix-it ticket. Officers can also use the stop to look at other issues, so it is smart to fix it before you roll.
How bright does a license plate light need to be?
Bright enough to make the plate legible from 50 feet at night under state law. Federally, FMVSS 108 sets a minimum of 8 lux at the target points for lamps built to the standard. More light is not better if it is uneven or causes glare on the plate.
Does a trailer need its own license plate light?
In general, yes. State statutes such as Louisiana’s extend equipment rules to trailers, semitrailers and pole trailers, and a plate displayed on a trailer has to be lit. Check your own state code for exact wording.
Should the plate light be on when my headlamps are off?
No, it is meant to come on with your headlamps and other required lighting. Oklahoma’s statute spells out that the plate lamp must be lit whenever the clearance lamps and headlamps, auxiliary driving lamps or fog lamps are lit. Wiring it into the same circuit is the simplest way to comply.
Sources
- Texas Transportation Code § 547.322 (FindLaw)
- RCW 46.37.050 (Washington State Legislature)
- Oklahoma Statutes § 47-12-204.1 (Justia)
- Maryland COMAR 11.14.03.08, Lighting (Cornell LII)
- Louisiana Revised Statutes, tail lamp provision
- Ohio Revised Code § 4513.05
- Kansas Statutes § 8-1706 (FindLaw)
- 49 CFR 571.108, FMVSS No. 108 (eCFR)
- License Plate Light Tickets (FindLaw)
- Improper display of a license plate in Arkansas (King Law Group)
- Waterproof license plate lights (PickSmartly)




